Module 1

Cardiovascular physics

Your heart is a pump and your blood vessels are pipes. Three plates take you from the simplest rule of circulation to the point where that rule stops working.

Plate 1.0

The heart as a pump

Two pumps share one muscle. The right side sends blood through the lungs and the left side sends it around the body. Drag to turn the heart, and click any part to see the physics behind it.

Schematic

Shapes are simplified and not to scale. Red marks oxygen-rich blood, blue marks oxygen-poor blood. The timing of each beat follows a real cardiac cycle.

Click a part of the heart.

Cardiac output

Plate 1.1

Pressure, resistance and flow

Blood moves from high pressure to low pressure. The bigger the pressure difference, the more blood flows. The more the vessels resist, the less blood flows.

Schematic

Particle speed rises and falls with the calculated flow. Plate 1.2 shows real speeds.

\[ Q = \frac{\Delta P}{R} \]
  • \(Q\) is the volumetric flow rate, in litres per minute
  • \(\Delta P\) is the pressure difference, in mmHg
  • \(R\) is the resistance of the vessels, in mmHg·min/L
Flow rate, \(Q\)

The starting values describe a resting adult. About 90 mmHg separates the arteries from the veins, the whole circulation resists with about 18 mmHg·min/L, and the heart pumps about 5 L/min. But where does that resistance come from? Plate 1.2 answers that.

Plate 1.2

Poiseuille’s law: why radius matters most

Zoom in on one 10 cm stretch of artery. Its resistance depends on the blood’s viscosity, the vessel’s length and, above all, its radius. Combine that with plate 1.1 and you get the Hagen–Poiseuille equation.

\[ R = \frac{8\eta L}{\pi r^4} \qquad\Longrightarrow\qquad Q = \frac{\Delta P}{R} = \frac{\pi r^4\,\Delta P}{8\eta L} \]
Idealized model

Radius drawn to scale. Arrows show the speed profile. Particle speeds are drawn to one scale across all settings.

Along 10 cm of a large artery, pressure falls by only about 1 mmHg.
Water about 0.7 · plasma about 1.2 · whole blood about 3.5 mPa·s
Flow rate, \(Q\)
Resistance, \(R\)
Reynolds number, \(Re\)
Average speed
Speed at the centre
Idealized model

Predict first

Suppose this vessel’s radius is cut in half and nothing else changes. What fraction of the flow is left?

Real-world changes

Each change starts from a 3 mm artery carrying blood at 3.5 mPa·s. In a real body, the heart and other vessels respond too, so these are single-segment estimates.

Plate 1.3

Where the model breaks

Poiseuille’s law is exact only for a steady, smooth flow of a simple liquid through a long, straight, rigid tube. Blood vessels are none of those things. The model is still useful, as long as you know which assumptions you are making.

The model assumesIn the bodyWhat that changes
Steady flow The heart pumps in pulses, so flow speeds up and slows down with every beat. In large arteries the speed profile is flatter than a parabola, and resistance changes during the beat.
Laminar flow True in most vessels. Turbulence can appear in the aorta at peak flow and just past narrowed valves or arteries. Turbulence wastes energy, so real flow is lower than predicted. The Reynolds readout in plate 1.2 warns you.
A Newtonian fluid with fixed viscosity Blood is a suspension of cells. It gets runnier the faster it flows, and behaves differently in vessels narrower than about 0.3 mm. A single viscosity value is a fair approximation in large arteries, and a poor one in capillaries.
A rigid tube Arteries stretch with each pulse and recoil afterwards. The stretch smooths the pulse and changes the radius during the beat.
A long, straight, uniform tube Vessels branch, curve and taper. Branches and bends add extra resistance that the equation does not include.

Coming next in this module